Emulatory IAR Systems

I-jet is a slim JTAG hardware debug probe; it connects via USB to the PC host running Windows. I-jet integrates seamlessly into IAR Embedded Workbench and is fully plug-and-play compatible.

Key components:

• Supports ARM7/ARM9/ARM11 and Cortex-M/R/A cores
  
• Seamless integration into the IAR Embedded Workbench IDE
  
• (IAR Embedded Workbench for ARM version 6.30.8 or later)
  
• Fully plug-and-play compatible
  
• Hi-speed USB 2.0 interface (480Mbps)
  
• No power supply required, powered entirely by the USB port
  
• Target power of up to 400mA can be supplied from I-jet with overload protection
  
• Target power consumption can be measured with ~200ÄžA resolution at 200kHz
  
• JTAG and Serial Wire Debug (SWD) clocks up to 32MHz (no limit on the MCU clock speed)
  
• Serial Wire Viewer (SWV) with UART and Manchester encoding
  
• Support for SWO speeds of up to 60MHz
  
• Download speed of up to 1MByte/sec
  
• Automatic core recognition
  
• Support for multiple JTAG devices with automatic chain detection and graphical display
  
• Direct download into flash memory of most popular microcontrollers
  
• Support for JTAG adaptive clocking (RTCK)
  
• Automatic JTAG/SWD detection
  
• JTAG voltage measurement and monitoring
  
• Supports target voltage range from 1.65V to 5V
  
• Standard MIPI-20 and MIPI-10 JTAG cables are included
  
• ARM-20 (0.1in x 0.1in) JTAG adapter is included
  

IAR J-Link is a small JTAG hardware debug probe; it connects via USB to the PC host running Windows. IAR J-Link integrates seamlessly into IAR Embedded Workbench and is fully plug-and-play compatible.

Key components:

• Any ARM7/ARM9/ARM11/Cortex-M0/M1/M3/M4/R4/A5/A8 core supported, including both JTAG and SWD.
  
• Renesas RX supported (requires RX adapter)
  
• Seamless integration into IAR Embedded Workbench
  
• Download speed up to 600 KB/sec *
  
• DCC speed up to 800 KB/sec *
  
• Max. JTAG speed 12 MHz
  
• Max. SWO speed 6MHz (v7)
  
• Support for ETB
  
• No power supply required, powered through USB
  
• Automatic core recognition
  
• Auto speed recognition
  
• All JTAG signals can be monitored, target voltage can be measured
  
• Support for multiple devices on scan chain
  
• 20-pin standard JTAG connector
  
• Optional adapter for 5V targets available
  
• USB and 20-pin flat cable included
  
• Wide target voltage range: 1.2V - 3.3V, 5V tolerant
  
• Optional power on pin 19, default is power on
  
• Outputs can be tristated (Effectively disabling the JTAG interface)
  

* Measured with ARM7 at 50 MHz, 12MHz JTAG speed.

Use with Renesas RX
When using IAR J-Link together with a Renesas RX target an adapter cable is needed.

J-Link Ultra is a JTAG/SWD debug probe for ARM/Cortex and Renesas RX CPUs. It is fully compatible to the standard J-Link and works with the same PC software.

Based on the highly optimized and proven J-Link, it offers even higher speed as well as target power measurement capabilities due to the faster CPU, built-in FPGA and High Speed USB interface. It connects via USB to a PC running Windows XP, Windows 2003, Windows Vista or Windows 7. J-Link Ultra has a built-in 20-pin JTAG/SWD connector.

Key components:

• Fully compatible to the standard J-Link
  
• Very high performance for all supported CPU cores
  
• Hi-speed USB 2.0 interface
  
• Serial Wire Debug (SWD) supported
  
• Serial Wire Viewer (SWV) supported
  
• SWV: UART and Manchester encoding supported
  
• SWO frequency up to 25 MHz
  
• Target power can be supplied
  
• Target power consumption can be measured with high accuracy (up to approximately 50 kHz)
  
• Direct download into flash memory of most popular microcontrollers supported
  
• Any ARM7/ARM9/ARM11, Cortex-M0/M1/M3/M4/R4 core support, including thumb mode
  
• Renesas RX supported (requires RX adapter)
  
• Automatic core recognition
  
• JTAG speed up to 25 MHz
  
• Seamless integration into the
• IAR Embedded Workbench IDE
  
• No power supply required, powered through USB
  
• Support for adaptive clocking
  
• All JTAG signals can be monitored, target voltage can be measured
  
• Support for multiple devices
  
• Fully plug and play compatible
  
• Standard 20-pin JTAG connector
  
• Wide target voltage range: 1.8V - 5.0V
  
• USB and 20-pin ribbon cable included
  
• TCP/IP server included, which allows using J-Link via TCP/IP networks
  
• Embedded Trace Buffer (ETB) support
  
• Target power supply: J-Link can supply up to 300 mA to target with overload protection
  

JTAGjet is an advanced, real-time, in-circuit debugging probe for high-end applications development. It is based on the JTAG boundary scan port, and is possible to integrate with IAR Embedded Workbench.

Key components:

• Support for ARM7 and ARM9
  
• Download speed exceeding 1 MB/sec
  
• USB 2.0 (480Mbps) connection to host PC
  
• Smart Flash Programmer
  
• JTAG chain Device Detection
  
• Variable (up to 30 MHz) and Adaptive JTAG clock
  
• Auto-sensing JTAG voltage
  
• Chameleon debugger software included
  
• Multi-core debugging available with add-on in Chameleon
  

JTAGjet is an advanced, real-time, in-circuit debugger for high-end applications development. It is based on the JTAG boundary scan port, and is possible to integrate with IAR Embedded Workbench.

Key components:

• Support for ARM7, ARM9, and Cortex-M
  
• Download speed exceeding 1 MB/sec
  
• USB 2.0 (480Mbps) connection to host PC
  
• Smart Flash Programmer
  
• JTAG chain Device Detection
  
• Variable (up to 30 MHz) and Adaptive JTAG clock
  
• Auto-sensing JTAG voltage
  
• Chameleon debugger software included
  
• Multi-core debugging available with add-on in Chameleon
  

JTAGjet is an advanced, real-time, in-circuit debugger for high-end applications development. It is based on the JTAG boundary scan port, and is possible to integrate with IAR Embedded Workbench.

Key components:

• Support for ARM7, ARM9, ARM11, Cortex-M, Cortex-A8/A9, and Cortex-R4
  
• Download speed exceeding 1 MB/sec
  
• USB 2.0 (480Mbps) connection to host PC
  
• Smart Flash Programmer
  
• JTAG chain Device Detection
  
• Variable (up to 30 MHz) and Adaptive JTAG clock
  
• Auto-sensing JTAG voltage
  
• Chameleon debugger software included
  
• Multi-core debugging available with add-on in Chameleon
  

JTAGjet-Trace for ARM is an advanced, real-time, in-circuit debugger used for debugging, testing, and verification of high-end applications. It is equipped with Embedded Trace Macrocell (ETM) trace, and supports all ARM7, ARM9, ARM11, and Cortex devices with ETM. Integration with IAR Embedded Workbench is possible.

Key features:

• Supports all ARM7, ARM9, ARM11, Cortex-M, Cortex-A8/A9, and Cortex-R4 cores equipped with ETM trace logic
  
• USB 2.0 (480Mbps) connection to host PC
  
• Available with a standard Mictor-38 target connector or 20-pin Cortex connector
  
• Silent, fan-less design
  
• Small form factor—fits in the palm of your hand
  
• Smart Flash Programmer
  
• Adaptive JTAG Clock & Voltage
  
• Chameleon debugger software included
  
• Multi-core debugging available with add-on in Chameleon
  
• Plain JTAG adapter for boards without ETM available
  
  
  Trace features
  
  
• Up to 400 Msamples/sec trace acquisition (400MHz CPU speed)
  
• Auto adjusting timing eliminates problems with data and clock skew
  
• Available with 4.5/ 9/18 MB trace buffer
  
• Support for 4, 8 and 16-bit wide trace busses
  
• 56-bit time stamp with CPU cycle accuracy down to 5ns
  
• Easy access to all ETM modes, triggers and filtering
  
• Only one connection to target–both JTAG and trace are taken from the 38-pin ETM Mictor, or 20-pin Cortex SWD header
  

JTAGjet-Trace for Cortex-M is an advanced, real-time, in-circuit debugger used for debugging, testing, and verification of high-end applications. It is equipped with Embedded Trace Macrocell (ETM) trace, and supports all Cortex-M devices with ETM. Integration with IAR Embedded Workbench is possible.

Key features:

• Supports Cortex-M cores equipped with ETM trace logic
  
• USB 2.0 (480Mbps) connection to host PC
  
• Available with a standard Mictor-38 target connector or 20-pin
• Cortex connector
  
• Silent, fan-less design
  
• Small form factor—fits in the palm of your hand
  
• Smart Flash Programmer
  
• Adaptive JTAG Clock & Voltage
  
• Chameleon debugger software included
  
• Multi-core debugging available with add-on in Chameleon
  
• Plain JTAG adapter for boards without ETM available
  
  
  Trace features
  
  
• Up to 400 MSamples/sec trace acquisition speed (up to 400 MHz CPU speeds)
  
• Auto adjusting timing eliminates problems with data skew
  
• Available with 4.5/ 9/18 MB trace buffer
  
• Support for 4, 8 and 16-bit wide trace busses
  
• 56-bit time stamp with CPU cycle accuracy for timing analysis
  
• Easy access to all ETM modes, triggers and filtering
  
• Only one connection to target–both JTAG and trace are taken from a high-density, 20-pin Cortex header
  

RX adapter for IAR J-Link

Add-on feature to IAR J-Link and IAR J-Link Ultra
(Part number: JLINK-RX-ADP)

The RX adapter allows IAR J-Link to be used for flashing and debugging Renesas RX target boards fitted with a 14-pin JTAG connector. The target can optionally be powered through IAR J-Link and the RX adapter.

19 pin adapter for ARM Cortex-M

Add-on feature to IAR J-Link and IAR J-Link Ultra
(Part number: JLINK-CM-ADP19)

The 19-pin adapter for ARM Cortex-M allows JTAG, SWD and SWO connections between IAR J-Link and Cortex-M based target hardware systems. It adapts from the 20-pin 0.1'' JTAG connector to a 19-pin 0.05'' Samtec FTSH connector as defined by ARM.

9 pin adapter for ARM Cortex-M

Add-on feature to IAR J-Link and IAR J-Link Ultra
(Part number: JLINK-CM-ADP9)

The 9-pin adapter for ARM Cortex-M allows JTAG, SWD and SWO connections between IAR J-Link and Cortex-M based target hardware systems. It adapts from the 20-pin 0.1'' JTAG connector to a 9-pin 0.05'' Samtec FTSH connector as defined by ARM.