|
|||||||||||||
|
 |
||||||||||||
| Home > Programmers > Uprog ICP |
Uprog ICP / USB |
||||||||||||||||||||||||||||||||||||||||||
Uprog ICP - new, flexible and powerful programmer designed to in-circuit programming tasks.
Powered through USB, Uprog ICP does not require external power supplier and supports wide
range of integrated circuits: microcontrollers (8051, PIC, AVR, MSP430, ARM, ST72, etc.),
serial EEPROMs & flash (I2C, SPI, Microwire, 1-wire, etc.), CPLD & FPGA.
Target device can be powered by the programmer (5V down to 1.8V), programming
voltage up to 14V can be also provided.Thanks to USB 2.0 interface and specialized microprocessor we achived short programming times close to vendor's maximum ratings. Uprog is able to working in High Speed and Full Speed modes. New software for Windows 2000 and newer systems was designed to intuitive operation. It supports many programmers simultaneously, so several programmers may be connected to the PC in order to increase efficiency of whole system.  Key features
In-circuit programming connector (ICP)
Uprog portable has Build-in interface for in-circuit programming,
so as to be able to program chips working via
SPI, I2C, BDM, JTAG, 1 WIRE, 3 WIRE
and others.
Serial programming interface was designed to allow to archive maximum data
speed transfer and allows to adjust signal voltage level for any technology.
Serial Programming Adapter assure: • adaptation of voltage levels (1.2V - 5V) • fast data transfer • flexible connection between programmer and programmed device • posibility to connect VPP, VCC, GND, CLK, and 6 universal IO pins. ICP allows to be pin-checked, so as to be able to keep good contacts with programmed chip. Ulogic - digital signal analyser (option).
Main features:• 16 input channels • maximum sampling rate: 200MHz1 • buffer length: 64K x 16 or 256K x 16 • short data transfer time • external clock input • flexible trigger settings: edge, level (pattern) or combination of edge and/or pattern • Pre-trigger and Post-trigger buffer • capture delay and edge counter feature • input impedance: 100kΩ • sampling booster - the area near Trigger may be sampled with double rate • serial protocol interpreter: RS-232, SPI*, I2C*, CAN*, 1-wire* (* - available soon) • state machine analyser • mnemonics code analyser for microprocessors • possibility of signal comparing (three independent buffers) • pattern genetrator Ulogic, the Uprog based logic analyzer, makes the programmer an excelent measurement tool. Simply connect probes to the connector at front panel, run software and enjoy capturing the data.
Notes:
Pattern generator (option)
Pattern generator is a tool designed for developing and testing of digital equipment.
Thanks to user friendly pattern editor user can define any sequence of 16 digital signals and apply them
to device's digital intetrface. Generated patterns are fully compliant with general standards of digital signals.
Exept possibility of pattern definition user can change voltage level of output signals.
Main features: • 16 output channels • Generation rates from 100MHz (state changes every 10ns) down to 200Hz • maximum buffer length: 64K samples (optionally 256K). • adjustable buffer length from 1 to maximal length • possibility of save defined signals for further use • available work modes: - Auto - generation of defined signals, - Repeat - cyclic generation of signals after trigger - Single - single generation of signals after trigger • adjustable voltage level of output: 1.8V, 2.5V, 3.3V, 5V (TTL). • user friendly pattern editor. Additional board with ZIF socket Uprog ICP Programming Socket (option)
The programmer can optionally be equipped with an additional board with ZIF socket
that allows non-ICP programmings of devices in DIL packages, or other after using package adapters.
Using short cables user is able to connect control signals from programmer's ICP socket
to respective pins of the device.
Package includes:
Gallery
Downloads
 |
||||||||||||||||||||||||||||||||||||||||||
